国产免费不卡_在线观看毛片网站_欧美金8天国_香蕉视频在线免费看_99re热这里只有精品视频_久久综合久_日韩专区欧美专区

Welcome to Changxing Baodi Environmental Protection Technology Co., Ltd!

中文版 | English
 
Your current position: Home >> What's the matter with the atomic gray printing on the automobile paint surface

What's the matter with the atomic gray printing on the automobile paint surface


What is atomic gray printing? Let me explain to you that the atomic gray mark is the edge of the coating under the topcoat visible system, or the grinding mark near the original repair area. This is the so-called atomic gray mark. I don't know if you can see it or not, just think about it slowly. Next, let's talk about why this happens?
The cause of atomic gray printing
1) The use of atomic ash on unsuitable substrates results in tension differences.
Atomic ash is used on inappropriate substrate, resulting in tension difference; before spraying polyester atomic ash, the substrate shall be analyzed first, and polyester atomic ash can only be used on bare steel or protective green primer.
2) Before grinding, the base material has not been degreased or degreased improperly. During grinding, the edge is out of shape, leaving an irregular edge around the repair area.
Before grinding, the base material has not been degreased or the degreasing is improper, which means that the atomic ash and the base material are not attached well. During grinding, the edge is out of shape, leaving an irregular edge around the repair area; therefore, we should thoroughly degrease before grinding.
3) The substrate to be scraped and coated with atomic ash shall be polished with fine sandpaper. After grinding, due to poor adhesion, the edge of atomic ash is out of shape.
For the substrate to be scraped and coated with atomic ash, use fine sandpaper to polish; after polishing, because of poor adhesion, the edge of atomic ash is out of shape; in this case, we should use the recommended thickness sandpaper when grinding and edging.
4) The repair interface area is not properly ground.
The repair interface area is not properly ground, and the repair interface area is fully ground
5) After the base material is polished too rough and the atomic ash is polished and leveled, there are still obvious sandpaper marks.
After the base material is polished too rough and the atomic ash is polished flat, there are still obvious sandpaper marks; therefore, the correct grinding steps should be adopted.
6) Minor patching areas in the paint system are not adequately edged.
The small patch area of the paint system is not fully ground, so the interface area of the small patch is fully ground.
7) The filled area is not smooth enough to be raised compared to the surrounding area.
The filling area is not polished smooth enough and protrudes significantly compared with the surrounding area; in this case, polish with grinding pad and touch the surface of the filling area from time to time.
8) Part of the atomic ash is scraped on the old paint film, and irregular edges are formed around the filling during grinding.
Part of the atomic ash is scraped on the old paint film to form an irregular edge around the filling area during grinding; the repair area is thoroughly polished.
9) The scraping of atomic ash is not smooth, and the edge is not polished.
The scraping of atomic ash is not smooth and the edge is not polished; when scraping and coating atomic ash, the edge shall be grinded.
In case of atomic gray mark on automobile paint surface, the repair area shall be polished, repaired to make it smooth, and then sprayed again.
Solution of atomic gray printing
1) Atomic ash can only be used on bare steel or protective primer.
2) Atomic ash shall be degreased thoroughly before grinding.
3) When grinding and edging, it is recommended to use coarse sandpaper.
4) Fully grind the repair interface area.
5) Take the correct grinding procedure.
6) Fully edge the interface area of small patch.
7) Grind with a grinding pad and touch the surface of the filled area from time to time.
8) Polish the repair area thoroughly.
9) When scraping and coating atomic ash, the edge shall be grinded.
10) Polish and trim the repair area to make it smooth, and then spray again.
Well, today, the solution of atomic gray printing on automobile paint surface introduced by Xiaobian is here. I don't know if you have a deeper understanding of atomic gray printing after listening to Xiaobian's introduction? I hope the introduction of Xiaobian can help you.


PrevBe careful when using atomic ash
NextWhat are the reasons for the shrinkage of atomic ash?

Copyright © 2020 Changxing Baodi Environmental Protection Technology Co., Ltd all reserved Web Admin --> >>

浙公網安備 33052202000243號?浙ICP備17019658號

主站蜘蛛池模板: 亚洲免费观看网站 | 久草5| 激情视频网| 国产无遮挡又黄又爽动态图 | 日本免费视屏 | 99在线精品免费视频 | 99re在线这里只有精品免费 | 久久精品伊人网 | 青青草影院在线观看 | 欧美三级视频在线播放 | 日本99视频 | 精品免费国产一区二区三区 | 天天干天天操天天舔 | 欧洲视频在线观看 | 日本高清色视影www日本 | 欧美在线一级精品 | 99午夜| 性久久久久久久久久 | www.日本在线视频 | 五月婷婷丁香综合网 | 韩国三日本三级中文字幕 | 九九热免费视频 | www在线观看免费视频 | 日日摸夜夜添夜夜添97 | 老子影院午夜伦不卡不四虎卡 | 日本特黄绿像大片免费看 | 欧美综合自拍亚洲综合百度 | 久久99爱re热视 | 久久97精品久久久久久久看片 | 精品久久一区二区三区 | 美女视频黄a视频全免费应用 | 99re在线视频 | 亚洲tv精品一区二区三区 | 一本一本久久a久久综合精品蜜桃 | 亚洲综合在线一区 | 在线观看www | 国产一区福利 | 国产日韩欧美亚洲综合在线 | 欧美性生交xxxxx久久久 | 国产一级一片免费播放刺激 | 中国xxxx视频播放免费 |